Sample Specs for a 70 Weaver

Construction:

  • 3 Layers 12 mm Okume plywood
  • 1 layer 1708 E-glass outside bottom impregnated with epoxy 1708
  • 1 layer 1308 Kevlar outside bottom impregnated with epoxy
  • Laminated Douglas fir stringers glass encapsulated
  • 1 layer 1708 E-glass inside bottom to chine
  • 1 layer 1308 Kevlar inside bottom to chine.
  • Hull side’s 3 layers 6mm Okume plywood
  • 2 layers E-glass outside impregnated with epoxy
  • Epoxy coated Okume from chine to sheer
  • Laminated Douglas fir battens, sheer clamp and chine
  • All bilges, engine room and pump room faired and painted
  • 3 layers 12mm Okume plywood on house sides
  • 2 layers 6mm Okume plywood on bridge floor
  • 1-layer E-glass impregnated with epoxy
  • ¼” tempered graylite 14 glass for side, back and door windows.
  • A buildup of epoxy mixed with sand able faring compound and block and sanded smooth.
  • Ablative/Copolymer anti-fouling bottom paint (3 coats), over Interlux Interprotect epoxy primer system
  • Awlgrip brass thru hulls and sea strainers in engine room and forward bilge
  • Awlgrip engine room, lazarette, forward bilge and anchor locker for enhanced visibility and easier maintenance
  • Dockside and overboard pump outs for holding tank
  • Awlcraft high gloss polyurethane boot stripe
  • Hatches, one (1) Bomar, fore-deck hatch with Ocean Air screen shade system
  • Spray able faring compound applied and sanded smooth
  • 6 primer coats of paint
  • Finish Paint
  • Paint Type – Awlcraft 2000

General Interior:

  • Interior cabinetry and doors to be custom crafted, wood to be determined from builder’s selection.
  • The Cabinetry is to be constructed with combination of plywood, Divinycell, tri-cell and Nida-core.
  • Countertops to be KVF
  • Brushed Nickel hardware is to be used throughout.
  • Wood flooring where specified to be selected by owner
  • Air conditioning – direct expansion, zoned with reverse cycle heat for complete climate control throughout the interior and with individual controls for staterooms and salon

Exterior Finishes:

  • Awlgrip 2000 paint
  • Teak covering boards
  • Teak toe rail with varnish finish
  • Teak cockpit floor
  • 1 1/8“solid Stainless-steel rub rail
  • Teak Transom
  • Teak bulkhead

General Specs:

  • 2000 +/- gal fuel capacity
  • 300-gal water capacity
  • 80 gal holding tank with 24vmacerator pump lined with epoxy
  • Marine Exhaust Linear Mufflers
  • Recessed trim tabs
  • Aluminum Fuel Tanks
  • Powers assist hydraulic steering with 2 Pumps
  • Oval Exhaust tips
  • 12” 24v bow thruster
  • Lewmar Windless
  • 16000 BTU Crusair with digital control for Fly bridge console and Mezzanine overhead

Décor

  • All hardware metal finishes satin nickel throughout
  • Designer bedspreads for all beds
  • Designer carpet, $40 per yard allowance
  • Designer fabrics by Kravet with $45 per yard allowance
  • Designer shams (2) per stateroom (3 for VIP forward layout)
  • Next Day Blinds silhouette
  • Interior finish satin, on vertical surfaces
  • Throw pillows throughout including designer cords and fringes
  • Ultraleather seating in salon and master stateroom and dinette
  • Upgraded window panel fabric and trim

Main Salon and Galley:

  • Sliding composite door, Teak on outside and veneer on inside, with electric door opener.
  • Electrical panel
  • 2 – 16,000 BTU AC – Crusair digital control
  • 110-volt recessed lighting LED
  • 24-volt accent rope lighting
  • Tinted tempered glass
  • Ultra Leather sofas and dinette constructed by Costa Marine Canvas, Inc.
  • Whisper Wall vinyl headliner
  • Air conditioning with reverse cycle heat that circulates from concealed registers behind the valances to maximize comfort while minimizing noise and drafts – individual temperature control
  • Blinds for desired natural lighting and additional privacy
  • Carpeting, wall-to-wall with lined padding for sound absorption $40 per yard allowance
  • Cocktail table, teak, high-gloss finish-hi/low
  • Custom wood flooring at salon entrance
  • Decorative throw pillows for sofa
  • Fixed, side windows with tinted, tempered glass for style, natural lighting, and privacy
  • Home theater center with 53” Samsung TV on a raise and lower mechanism with antenna or cable hook-up, and Bose stereo with surround sound, aux audio input jacks to accommodate additional equipment
  • Lambrequins, fabric upholstered-inlaid in teak frames
  • Lighting, overhead LED lights recessed in headliner with dimmer switches and direct decorative rope lighting behind valances, 24 VDC
  • L-shaped lounge with lift cushions for storage
  • Main electrical panel with AC selector breakers
  • Whisper Wall headliner, owner’s choice of color, 1/8” foam and tricot backing
  • Teak cabinetry with drawers and bottle storage, finished veneer interior
  • Valances solid teak, fluted with solid teak blind covers
  • Custom wood flooring in Galley
  • Custom galley island, 360-degree access with refrigeration and freezers, KVF countertop
  • Dinette couch with removable cushions and storage underneath
  • Dinette table, teak, high-gloss finish with oversized teak pedestal, thru-bolted
  • Electric range, 4-burner cook top, surface-mounted
  • Exhaust fan, high velocity designed for exterior ventilation
  • Garbage disposal in sink
  • Ice maker, clear ice type concealed in companionway
  • LED lighting-backsplash
  • Lighting, overhead LED lights recessed in headliner with dimmer switches
  • Microwave/convection oven located in upper galley cabinet
  • Pantry, port side aft of companionway stairs
  • Sink, double-bowl stainless steel, under-mounted in countertop with satin nickel galley faucet
  • Stools – (3) swivel type bar stools on aft side of galley island
  • Storage cabinets in upper galley, varnished teak doors with finished maple interior
  • Storage cabinets and drawers in lower galley, varnished teak doors and faces with stowage for utensils, and other items
  • Storage above dinette
  • Water tank level gauge in pantry
  • KVF countertops and sink with Grohe single lever faucet
  • Appliances:
    • Ice Maker – Whirlpool
    • Refrigerator – 1 Subzero drawer systems (1 drawer)
    • Freezer – 2 Subzero drawer systems (4 drawers)
    • 4-burner cook top with exhaust fan
    • Microwave/Convection – GE
    • Garbage disposal

Master Stateroom:

  • Queen style bed with drawers and storage
  • Soft goods by Costa Marine Canvas, Inc. including bedspread and pillows
  • 12000 BTU Crusair – Digital control
  • Cedar lined hanging closets
  • 110v recessed lighting or LED
  • 24v accent rope lighting
  • Private access to master head
  • Wisperwall walls
  • Carpet on floors with a $40 per yard allowance
  • Air conditioning with reverse cycle heat that circulates from concealed registers behind the valances to maximize comfort while minimizing noise and drafts – individual temperature control
  • Decorative LED indirect rope lighting from underneath bed platform
  • Drawer storage under bed, (2) large drawers, for forward and aft bank
  • End tables each side of bed
  • Headboard, upholstered
  • Lighting, overhead LED lights recessed in headliner with dimmer switches
  • Whisper Wall headliner, owners color selection, 1/8” foam and tricot backing
  • Mattress, Handcraft, Innerspring System
  • Pillow shams (2), with throw pillows
  • Reading lights, overhead with separate switches
  • Telephone outlet
  • TV, 38” Samsung flat screen

Master Head:

  • Fresh Water Flush Raritan Atlantes Head
  • Custom fiberglass shower with Grohe faucet and Rule 800 sump pump
  • Fresh water flush Raritan head
  • A/C Supply
  • Wallpapered walls
  • Air conditioning/heat with register
  • Custom wood flooring
  • Exhaust fan with vent in soffit
  • Guest Head, One-piece counter top KVF with sink and satin nickel faucet
  • Lighting, overhead LED lights recessed in soffit and in ceiling
  • Linen Storage with shelves and mirrored door in master head
  • Lower vanity with curved teak face
  • Master Stateroom head countertop, KVF
  • Master Stateroom head, one-piece custom frameless shower doors
  • Medicine cabinet with mirrored doors
  • Mirror around upper vanity insert
  • Receptacle, 120V – GFCI
  • Shower light
  • Stall shower, fiberglass with satin nickel shower fixtures and with drain to automatic sump pump in bilge
  • Towel bar and ring – satin nickel

VIP Stateroom:

  • Double style bed with drawers and cedar lined storage under
  • Soft goods by Costa Marine Canvas, Inc. including bedspread and pillows
  • Cedar lined hanging locker
  • 32” Samsung TV
  • 12000 BTU Crusair with digital control
  • 110v-recessed lighting
  • 24v accent lighting
  • Wisperwall walls
  • Carpeted floors with a $40 per yard allowance
  • Bomar Hatch with screen and shade
  • Air conditioning/heat with temperature control
  • Decorative LED indirect rope lighting from underneath bed platform
  • Lighting, overhead LED lights recessed in headliner with dimmer switches
  • Whisper Wall headliner, owner’s choice color, 1/8” foam and tricot backing
  • Queen over-sized walk-around bed with mattress and lift up top with gas pistons and storage underneath
  • Reading lights with separate switches
  • Storage cabinets, port and starboard sides of bed, teak
  • Storage drawers under bed, (2) large drawers

VIP Head:

  • Freshwater Flush Raritan head
  • Wallpapered walls
  • Access from guest quarters
  • Air conditioning/heat
  • Custom wood flooring
  • Exhaust fan with vent in soffit
  • Guest Head, KVF Corian countertop with rounded edges and sink with satin nickel faucet
  • Lighting, overhead LED lights recessed in soffit and in ceiling
  • Lower vanity with curved teak face
  • Medicine cabinet with mirrored doors
  • Mirror around upper vanity insert
  • Receptacle, 120V – GFCI
  • Shower light
  • Stall shower, fiberglass with satin nickel shower fixtures and with drain to automatic sump pump in bilge
  • Towel bar and ring – satin nickel

Crews Quarters:

  • Soft goods by Costa Marine Canvas, Inc. including bedspread and pillows
  • 19” Samsung TV
  • 24v accent lighting
  • Carpeted floors with a $40 per yard allowance
  • (2) bunk lights
  • Air conditioning/heat with temperature control
  • Bedspread – quilted, designer style
  • Decorative indirect rope lighting from underneath bed platform and behind valances
  • Hanging locker, teak, cedar-lined with bar for hanging clothes
  • Lighting, overhead LED lights
  • Whisper Wall headliner, owner’s choice color, 1/8” foam and tricot backing
  • Storage drawers located under hanging locker
  • Upper/lower bunks with mattress and lift up bottom for storage

Guest Quarters:

  • (2) bunk beds with mattress and lift up bottom for storage in both staterooms
  • 32” Samsung TV
  • Wisperwall walls
  • Carpeted floors with a $40 per yard allowance
  • (2) bunk lights
  • Air conditioning/heat with temperature control
  • Bedspread – quilted, designer style
  • Decorative indirect rope lighting from underneath bed platform and behind valances
  • Hanging locker, teak, cedar-lined with bar for hanging clothes
  • Lighting, overhead LED lights
  • Whisper Wall headliner, owner’s choice color, 1/8” foam and tricot backing
  • (2) Pillow shams

Guest Head / Crew Head:

  • Freshwater Flush Raritan head
  • Wallpapered walls
  • Access from Guest Quarters
  • Air conditioning/heat with register
  • Custom wood flooring
  • Exhaust fan with vent in soffit
  • Guest Head, KVF countertop with rounded edges and sink with satin nickel faucet
  • Lighting, overhead LED lights recessed in soffit and in ceiling
  • Linen Storage with shelves and mirrored door in master head
  • Lower vanity with curved teak face
  • Guest Stateroom head countertop, KVF
  • Guest Stateroom head, one-piece custom frameless shower doors
  • Medicine cabinet with mirrored doors
  • Mirror around upper vanity insert
  • Receptacle, 120V – GFCI
  • Shower light
  • Stall shower, fiberglass with satin nickel shower fixtures and with drain to automatic sump pump in bilge
  • Towel bar and ring – satin nickel

Companionway:

  • Wisperwall walls
  • Awlgrip bilge areas with access hatches, snow white and lighted for easier maintenance and cleaning
  • Carpeting, carpeted steps from galley through companionway $40 per yard allowance
  • Central vacuum unit connection with accessories
  • Laundry center with stackable, front-loading washer and dryer behind teak door
  • Lighting, overhead LED lights recessed in headliner

Fly bridge open:

  • Electrical panel for electronics (16 breakers)
  • Horn
  • Running lights
  • Fuel Transfer switch with flow indicator lights
  • High Water Alarms
  • Bilge pump lights
  • Genset indicator light
  • 110-volt electrical outlet
  • Fresh water wash down under seat
  • Back-up engine controls supplied by engine manufacturer
  • Custom helm pod with single lever electronic controls
  • Engine shutdown switches at cabinet in console
  • Extended overhang for extra room to move behind helm and companion seats with anodized aluminum aft railing
  • Fire system control with automatic and manual discharge and override system located at console
  • Fresh water outlet forward locker
  • Freezer, top-loading, for bait and food storage, forward
  • Gauges/electronic displays, include hour meter reading for main engines supplied by manufacturer
  • Handrails, powder-coated aluminum effectively positioned above ladder to bridge and at helm
  • Helm and companion seats, 2 seats, teak, ladder back with 4” stainless pedestals and removable cushions and covers by Release Marine or Murray
  • Instrumentation based on standard engine package, lighted with switches in radio box
  • Lighted Ritchie compass, large and flush-mounted on centerline
  • Lounge seating to port and starboard and at forward end of helm console with vinyl covered foam cushions, hinged for access to storage under seats
  • Non-skid deck for traction and durability
  • Recessed electronics box in console for custom electronics package that is easily viewable and protected from the elements by Teak fitted lid with gasket and stainless-steel gas pistons
  • Recessed radio boxes, large radio boxes on port and starboard sides of console with switch panel inside
  • Refrigerated drink box forward starboard cabinet
  • Removable fly bridge bench seat backrest forward facing at aft ends of port and starboard bench seats
  • Trim tab control switch mounted at console
  • (2) Trumpet style air horns
  • Under helm access with lights

Running Gear:

  • Flush mount stainless steel struts
  • (2) Aquamet 22, 3½” shafts
  • 5 blade Nibral propellers Michigan
  • (2) 2 ¾” Stainless steel rudders
  • Dripless rudder ports and glands by Tides Marine
  • Shaft tube with dripless shaft seals by Tides Marine
  • Custom raw water sea chest-grate

Forward deck:

  • Large Anchor locker with drain
  • Fresh water-wash down in anchor locker
  • Fortress Anchor with 30’ chain and 300ft of ¾ nylon rope
  • Non-skid walk area
  • (4) cleats
  • (1) Bowmar hatch with shade and screen

Cockpit:

  • Raised mezzanine with seating area
  • Cockpit ladder with teak treads
  • Salt & Fresh water wash down in cockpit
  • Salt water wash down pump
  • Stainless steel bait freezer
  • Stainless steel lined travel freezer
  • Tackle drawers with stainless steel drawer guides
  • Engine room entrance
  • Transom tuna door with stainless steel drawer guides
  • Teak covering boards
  • (6) rod holders in covering boards
  • Eskimo crushed ice machine with ice storage
  • (2) recessed stereo speakers in overhang
  • (3) recessed air circulation vents
  • Stainless steel hawse pipes in transom corners
  • (2) 15” cleats
  • Lazarette access
  • (4) under water lights ocean led colors pro series 4 in transform 2 on each side
  • Release Marine or Murray Brothers Fighting Chair (and below items)
    • Teak seat upgrade 23 x 23 with 36” footrest
    • (1) 6- hole chair launcher, teak, (4) 15º no bolt rod holders
    • Bait tray teak- includes non-skid
    • Back pad teak- 12º curved
    • Tackle drawer teak face with starboard drawer
    • Fighting chair cover
    • Aluminum backing plate, laminated in cockpit sole, for fighting chair or table
  • Cable TV and telephone connections in cabinet under port forward gunwale wired to a home runs in entertainment center
  • RG6 TV cable to accommodate satellite system
  • Dockside electric connection – (2) 50 amp/220V
  • Dockside water connection with pressure reducing valve in cabinet under gunwale
  • Engine room access with door and steps to engine room
  • Extended flybridge overhang for shade
  • Fresh water wash down with hose bib located in cabinet under gunwale
  • Indirect rope lighting underneath the coaming (LED)
  • Ladder to flybridge, one-piece, anodized aluminum
  • Lazarette hatch with access to steering system, trim tabs, drain pumps
  • Lighting, recessed LED deck lights in flybridge overhang
  • Observation mezzanine with starboard aft facing lounge seating with Sunbrella covered cushions, hinged seats, tackle cabinet
  • Stainless steel oversized refrigerated chill box in mezzanine step for direct access from cockpit
  • Self-bailing cockpit with large scuppers
  • Stainless steel gas springs on all hatches and lids
  • Stereo speakers tied into salon stereo with remote control
  • Straps with padding to secure transom door and gate while open
  • Valve to fill freshwater tank from dockside inlet

Engine Room and Mechanical:

  • (1) 16,000 Sea Keeper Gyro
  • (2) 21.5 KW Onan Genset with Sound shield
  • (2) CAT C32 ACERT 1925 HP with Twin Disc MGX6599A
  • 1200GPD Sea Recovery Water Maker
  • Livos mist eliminators
  • Aluminum stringer caps
  • (4) 24V exhaust fans
  • (2) 230V Fresh water pumps
  • 30-gal stainless steel hot water heater
  • 110 volts and 24-volt engine room lighting
  • Eskimo ice machine- 600 lb. per day
  • Battery chargers (1) 240-volt 60 amp & (1) 24volt 10 amp
  • Racor filters – dual on engines – single on generators
  • Batteries – (8) Deka group 27
  • Battery switches – Blue Sea Systems 660-amp rotary switches
  • Crusair compressor for drink box and cockpit freezer
  • Crusair compressor for travel freezer
  • (4) bilge pumps – 3 with high water alarms
  • Sea strainer on Gensets
  • 24-volt water-wash down pump with strainer
  • Fuel sight gauges
  • Water and holding tank gauges
  • External sea strainers for main engine pick-ups
  • Fire suppression system, automatically and manually operated and tied into main engine and generator ignition and ventilation systems with override
  • Fresh water filter – paper
  • Fresh water supply in engine room for general maintenance and cleaning
  • Fuel transfer, 24 VDC pump Oberdorfer
  • Hour meters on generators
  • Internal sea strainers for generator, and all other sea water pickups
  • Mufflers – engines, in-line type with surge tubes in engine room
  • Mufflers – generators, gas/water separators
  • Multi stage speed 110V AC fresh water system with on deck fresh water fill and cockpit dockside supply inlet with pressure reducing valve
  • Oil changing system, gear type pump for main engines, transmissions, and generator with pump out line run to cockpit locker
  • PEX plumbing, fresh water system with manifold system to isolate individual areas
  • Propellers, Class “S” pitch tolerance (ISO 484/2) and dynamic balancing. Advanced design cambered blade sections for optimum performance. Interceptors strips to adjust engine load. Nibral alloy for maximum durability.
  • Racor fuel/water separator filters for main engines and single for generator.
  • Rudders, stainless, composite rudder bearing with dripless seal laminated into hull
  • Seacocks, bronze, ball-type sea valves for all thru- hulls below the water line – Awlgrip snow white
  • Shafts – 2 Aquamet high-strength stainless steel, double-taper with machined keyway and main engine couplings
  • Struts – thru-water, stainless steel Nibral, with cutlass bearings
  • Tides Marine water lubricated dripless shaft seals with crossover water supply from both engines
  • Trim tabs, port and starboard tabs recessed in transom, individual controls for each tab with fiberglass covers

Plumbing:

  • Hot & cold-water supply
  • Indel Webasto 30-gal stainless steel hot water heater
  • (2) 230-volt Scott water pumps
  • 300 gal built in fresh water tank
  • 85-gal Aluminum holding tank lined with epoxy
  • Rule 2000 pumps for showers with 15-gal tank and float switch

Electrical:

  • Wired to ABYC standards All Wires to be labeled at each end
  • (2) 50 amps 125/250 volt – AC shore power cords
  • (2) 50 amps 125/250 volt – AC shore power inlet at port forward cockpit
  • Phone and cable outlet
  • Paneltronics Panels
  • Dyna plate bonding system
  • Transom mounted zinc
  • All necessary wiring to supply all specified 110 volts and 220-volt systems
  • Crusair, Eskimo Ice, water maker, dryer and water heater systems to be 220 volts
  • 24V DC ship’s service throughout
  • 240/120V AC power supply
  • 110V outlet in engine room on aft bulkhead
  • Anchor light/navigation lights
  • Battery chargers, (2) with thermal cutoff and switching system for complete integration
  • Battery distribution panels with battery cutoff for ship service batteries and engine batteries
  • Bonded electrical system with ground plate
  • Dimmers, DC LED interior lighting throughout excluding companionway
  • Engine room lights, recessed AC and DC with switch at engine room entrance
  • Lighting, overhead LED lights recessed in ceiling and rope style décor lights concealed by teak valances

Full Tower:

Tuna Tower with Molded Top 70’ Sportfish 9’ Gap, Polish Pipe

  • (2) Antenna, stands-offs, no Halyards, 3-sided track on perimeter rail.
  • (6) Hardtop lights to be Tri-color Lumitec Lights with fiberglass recess (blue, white & red)
  • (1) Radar Pod: Large oval style, mold #973, w/Sliding door for teaser reels
  • (1) Molded standing platform with coupler box on platform
  • (1) Molded 2 in 1 24V LED light pod with S/S Bezel
  • (1) Molded 24V-LED Light Fwd platform S/S Bezel
  • (1) Control box 63” with flush mounted compass
  • (2) Recessed electronics box with lid
  • (1) Paint top of control box satin black
  • (1) Bridge ladder no handrails (Weaver to fabricate and install teak steps)
  • (2) Handrails full length salon window (Weaver to paint)
  • (1) Tower sunshade molded with internal tracks. (5) Welded Antenna Mounts
  • (1) Molded satellite TV mount tower sunshade
  • (1) Paint tower sunshade frame satin black
  • (1) Bench seat with backrest
  • (1) Bridge rail, leg to leg, double aft to outer main leg
  • (8) Rod holder polished weld to rail PBT style
  • (6) Rod holder polished aft legs 3-P-3-S PBT style
  • (1) 46’ outrigger Rupp Bigg Riggs, HD 4 spreader, bridge release large solid aft bar
  • (1) Install outrigger Rupp
  • (1) Install Rupp hydraulic system
  • (1) Flag staff aft
  • (1) Nav. Lights port, stbd, stern molded
  • (2) Tri-color LED lights with fiberglass recess underside sunshade top
  • (2) Tri-color LED lights under platform with fiberglass recess
  • (1) Upgraded tower FWD X brace, side diagonals, and hardtop brace to contour style

Electronics:

  • All electronics are to be supplied by the owner.